900 MHz Manuals & User Guides
Please provide the user guides and manuals for the LMS4000 and LMS8000 900 MHz system. This includes the CCU3100, SL-900, CCU3000, EUM3000, EUM3003, EUM3004, EUM3005,...

How do you access the CCU3000, EUM3000, EUM3003, EUM3004 or the NCL1170 if you have forgotten your password?
The WaveRider CCU3000, EUM3000, EUM3003, EUM3004 and NCL1170 password can only be recovered by a keymatch challenge. Contact WaveRider support through an...

Is there a way to reset the CCU or EUM remotely?
If the CCU or the EUM can be accessed with SNMP, you should be able to reset the radios using Wave Rider’s GlobalReset MIBs. The MIB names and OIDs are as follows:...

CCU3100 Installation Guide
Please provide the user or install guide for the CCU3100 radio. This manual describes how to install the CCU3100. CCU3100 Installation Guide  

900 MHz nomadic (mobile) wireless modem manual
Please provide the user guides and manuals for the 900 MHz nomadic (mobile) wireless modem MMT9000. This manual describes how to install and configure the MMT9000,...

Please provide the latest product software for the 900 MHz product line including the CCU3000, NCL1900, EUM3000, EUM3003, EUM3004, EUM3005, EUM3006
Latest Software for the CCU3000, NCL1900, EUM3000/3/4 Latest software release for EUM3005 & EUM3006 . This release allows communication with Next Generation...

How do I access the EUM3000, EUM3003 and EUM3004 prior to software version 5.0?
Please refer to the following document.   Pre_v5-0_Access_Inop_900M_Product

CAP site is in production environment. All customers are experiencing slow Internet access.
First step would be to narrow down the problem to one or more of the following areas: - RF Network IP Network Backhaul. RF Spectrum sweep at the CCU and, a close...

Subscribers cannot ping pass the gateway router
This typically indicates that customers cannot access the Internet. If this is the issue, it is important to know if the customers are using Public (Registered IP) or a...

NCL1900 Installation Guide
Please provide the user guides and manuals for the NCL1900. NCL1900 Installation Guide Please also reference the library of manuals for the LMS4000 900 MHz...

Can I use the LMS3000 Grade of Service, GOS, Creation Utility with the CCU3100?
The LMS3000 Grade of Service Creation Utlity was designed to create grade of service files for the CCU3000 model only. Grade of service files from this utility will not...

Can the frequency search table be configured on a EUM3005, EUM3006 and MMT9000?
Yes, the command to make this change is <radio search add <freq>>.  This command adds a frequency to the list of frequencies to search. By default all...

Only subscribers close to the cap site are getting the expected throughput.
RF interference at the cap site or an overall drop of RF signal level in the coverage area is the most likely causes. If the RSSI Levels at all the subscriber modems...

What are the Temperature and Humidity specs for the 900 MHz Base Stations (CCU) and Subscriber Modems (EUMs)?
The following are the Environmental Specifications for the Base Station (CCU) and Subscriber Modems (EUM).   MODEL...

What is the latency of the LMS4000 900 MHz system?
WaveRider proprietary Dynamic Polling Mac is designed to work in a Point-to-Multipoint topology and intended to serve hundreds of average Internet users from a single base...

900 MHz Manuals & User Guides

What is the EUMID or serial number ranges for each LMS4000 EUM models?

What are the additional UDP and TCP ports used by Microsoft Vista?

NCL5800 Latency Benchmarks

What is the radio specifications (max user data rates (throughput / speed / receiver sensitivity,Rx threshold ) per modulation and modulation scheme number) for the LMS8000/CCU8000/EUM8000/NCL8000?

Why does the EUM8000, 8012, 8005, keeps using CCK2 modulation when the adaptive modulation is set for 5 to 11 on the EUM and CCU?

What is the number of OFDM subcarriers,subchannels carriers, data points, does the LMS8000, CC8000, EUM8000 uses?

Downtilting the Main Beam of an Antenna

Antenna Null Fill

Can I transfer the configuration files from an LMS4000 CCU to an LMS8000 CCU ?

What are the temperature limitations on the LMS8000, EUM8000, EUM8005, EUM8012?

Is it recommend to tape the Ethernet dongle on a EUM3006, EUM8000, CCU8010, NCL900, SL900, NCL8000, LMS8000?

What is the frequency range of the low loss band pass filter?

What is the specifications for the EUM3006, EUM8000 EUM8012, CCU8000 PoE Surge Suppressor?

Do you have any configuration sample describing the configuration of a Relay Agent Information on a DHCP Server that supports this option (RFC3046)?